概述If a SIMATIC S7-300-based system is to communicate with a Siemens control center, e.g. SIMATIC PCS7 TeleControl, WinCC TeleControl, WinCC OA, or a control center of a third-party supplier using the IEC60870-5 telecontrol standard, the IEC 60870-5-101 (serial), -103 (protection) or -104 (TCP/IP) telecontrol protocols can be used in the SIMATIC automation systems.SIPLUS RIC libraries offer an integrated, scalable system based on SIMATICS7-300 functions, for the following data quantities:? 200 information points, for use with CPU314? 1000 information points, for use with CPU315? 2000 information points, for use with CPU317? 5000 information points, for use with CPU319The non-retain memory can also be used for buffering message frames. Longer communication failure times can thus be bridged. The SIPLUS RIC software libraries are based on the standard SIMATIC Manager or TIA Portal and can be used on various, mutually compatible types of SIMATICS7 devices – this saves hardware costs and programming overhead.The libraries on CD are supplied together with a SIMATIC memory card, which can be used on all CPUs. Two versions with different memory sizes are available for selection.With SIPLUS extreme hardware, telecontrol devices for an extended ambient temperature range (-40...+70°C) and exceptional exposure to media (conformal coating) can be implemented using the telecontrol protocols.A license certificate with the activation of all telecontrol protocols IEC 60870-5-101 (serial), -103 (protection) or -104 (TCP/IP) is supplied for the SIMATIC memory card included in the scope of delivery.Note:The SIPLUS RIC libraries for S7-300completely replace the previous SIPLUS RIC S7-300 bundles und SIPLUS RIC S7-300 extreme bundles.單個項目:可以在可任意選擇的單個項目中更新不是多重項目的主數據庫(如 PCS 7 庫)的庫中的塊類型。
對于這中集中式類型比較,還將調整所有關聯的塊實例。
裝載程序以進行測試:經過修改的程序可裝載到測試系統中(另一個 CPU 或 PLCSIM)以便在將程序裝載到目標程序之前測試更改的效果。
使用“裝載到測試 CPU”(Load into test CPU) 功能(S7 裝載對話框中的選項),程序將保留裝載修改內容的功能。
全局聲明:在 SIMATIC Manager 的組件視圖中,可以為每個項目選擇“全局聲明”(Global declarations) 文件夾。
該文件夾包含子文件夾“計數器”(Counters) 和“單位”(Units)。
“單位”(Units) 文件夾已包含隨 CFC 安裝的單位的列表;含有計數值的“計數器”(Counters) 文件夾中的計數必須手動插入或聲明。
版本標識:在版本管理中,在創建可以在對象屬性中更改或與組態數據的相應工作狀態匹配的圖表、SFC 類型和全局聲明時,將向它們分配版本號。
組態歸檔變量:不歸檔歸檔長期歸檔基本功能編輯器功能除了已熟知的 Windows 應用程序的標準功能外,CFC 編輯器還提供了以下功能:通過雙擊塊提供上下文環境導航:根據在塊上進行雙擊的位置,將出現相應對話框:塊標頭:對象屬性塊“運行時屬性”(Run-time properties) 字段:運行時編輯器(可在這里標記相應的塊)。
塊體:打開下層圖表(對于圖中圖布局)。
導入、放置、復制、移動、刪除塊。
6ES7518-4AP00-0AB0CPU 1518-4 PN/DP,3 MB 程序,10 MB 數據, 集成3PN,1DP6ES7517-3AP00-0AB0CPU 1517-3 PN/DP, 2MB程序,集成 2PN 接口,1 以太網接口,1DP 接口6ES7516-3AN00-0AB06ES7516-3AN01-0AB0CPU 1516-3 PN/DP:1 MB 程序,5 MB 數據;10 ns ;集成 2PN 接口,1 以太網接口,1DP 接口6ES7515-2AM00-0AB06ES7515-2AM01-0AB0CPU 1515-2 PN ,500K程序,3M數據,集成 2PN接口6ES7513-1AL00-0AB06ES7513-1AL01-0AB0CPU 1513-1 PN:300 KB 程序,1.5 MB 數據;40 ns;集成 2PN 接口,6ES7511-1AK00-0AB06ES7511-1AK01-0AB0CPU 1511-1 PN:150 KB 程序,1 MB 數據;60 ns;集成 2PN 接口,6ES7512-1DK00-0AB06ES7512-1DK01-0AB0CPU 1512SP-1 PN, 200KB 程序,1MB數據6ES7510-1DJ00-0AB06ES7510-1DJ01-0AB0CPU 1510SP-1 PN, 100KB 程序,750KB數據6ES7507-0RA00-0AB0PS:60 W,額定輸入電壓 AC/DC 120/230 V6ES7505-0RA00-0AB0PS:60 W, 額定輸入電壓 DC 24/48/60 V6ES7505-0KA00-0AB0PS:25 W,額定輸入電壓 DC 24 V6ES7532-5HF00-0AB0AQ 8:模擬輸出模塊,8AQ,U/I ,高速6ES7532-5NB00-0AB0AQ 2: 模擬輸出模塊,2 AQXU/I ,標準型,25mm,包含前連接器6ES7532-5HD00-0AB0AQ 4:模擬輸出模塊,4AQ,U/I6ES7531-7NF10-0AB0AI 8:模擬輸入模塊,8AI,U/I,高速6ES7531-7QD00-0AB0AI 4: 模擬輸出模塊: XU/I/RTD/TC ST, 25mm,包含前連接器6ES7531-7KF00-0AB0AI 8:模擬輸入模塊,8AI,U/I/RTD/TC6ES7534-7QE00-0AB0AI4/AQ2:模擬量輸入/輸出模塊4AI,2AO,標準型,25mm,包含前連接器6ES7523-1BL00-0AA0DI/DQ 16X24CDV/16X24VDC/0.5A BA,包含前連接器.6ES7522-5HF00-0AB0DQ 8:數字輸出模塊,8DQ,繼電器,230 V AC/ 5A6ES7522-5FF00-0AB0DQ 8:數字輸出模塊,8DQ,可控硅,230V AC/ 2A6ES7522-1BL00-0AB0DQ 32:數字輸出模塊,32DQ,晶體管,24 V DC/ 0.5A6ES7522-1BH00-0AB0DQ 16:數字輸出模塊,16DQ,晶體管,24 V DC/ 0.5A6ES7522-1BF00-0AB0DQ 8:數字輸出模塊,高性能 8DQ,晶體管,24V DC/2A6ES7522-1BL10-0AA0DQ 32x24VDC/0.5A BA,包含前連接器6ES7522-1BH10-0AA0DQ 16x24VDC/0.5A BA,包含前連接器6ES7521-1FH00-0AA0DI 16:數字輸入模塊,16DI,230V AC BA6ES7521-1BL00-0AB0DI 32:數字輸入模塊,高性能 32DI,24V DC6ES7521-1BH50-0AA0DI 16:數字輸入模塊,源型,16DI, 24V DC BA6ES7521-1BH00-0AB0數字輸入模塊,高性能 16DI,24V DCIf a SIMATIC S7-400/S7-400H-based system is to communicate with a Siemens control center, e.g. SIMATIC PCS7 TeleControl, WinCC TeleControl, WinCC OA, or a control center of a third-party supplier using the IEC60870-5 telecontrol standard, the IEC 60870-5-101 (serial), -103 (protection) or -104 (TCP/IP) telecontrol protocols can be used in the SIMATIC automation systems.SIPLUS RIC libraries offer an integrated, scalable system based on SIMATICS7-400/S7-400H functions for the following data quantities:? 1000 information points, for use with CPU412 or CPU 412H? 2000 information points, for use with CPU414 or CPU 414H? 5000 information points, for use with CPU 410H, CPU416/CPU 416H or CPU 417/CPU 417HThe work memory for data which is limited to 256 MB in the CPU410H for data blocks generated online is used for buffering the frames. Longer communication failure times can thus be bridged. The SIPLUS RIC software libraries are based on the standard SIMATIC Manager or TIA Portal and can be used on various, mutually compatible types of SIMATICS7 devices – this saves hardware costs and programming overhead.The libraries are supplied on a CD and can be used on all CPUs.A memory card (CPU V5.0 or higher) or a CPU (CPU V4.x or higher and CPU410H) are licensed. All IEC 60870-5-101 (serial), -103 (protection) or -104 (TCP/IP) telecontrol protocols are activated via the email addresssiplus-ric.automation@siemens.com.The SIPLUS RIC libraries for S7-400completely replace the previous SIPLUS RIC S7-400 bundles, SIPLUS RIC S7-400 extreme bundles, and IEC60870 libraries for SIMATIC PCS7.